- The ever-popular 1/8th scale EP buggy has been renewed with even more fighting power.
- The Inferno series boasts an unrivaled track record in 1/8 scale GP buggy racing.
- Since its debut in 1991, it has continued to evolve, and the latest model, MP10 TKI2, is still active on the front lines of the world.
- The electric (EP) version of such MP10 TKI2 has appeared.
- In 2020, the EP model MP10e was released and demonstrated high competitiveness in the race, but as the popularity of 1/8 EP buggy increased worldwide, the number of races held increased and the rivals became stronger. I'm here.
- Therefore, we injected the essence of the GP model MP10 TKI2 into the MP10e and evolved it into a higher level machine.
- The MP10e TKI2 incorporates various innovations, but the biggest change in appearance is the adoption of a new body.
- The aerodynamic performance has been revised to match the speed of the race, and the speed has increased especially in the mid-range corners.
- As a result corner exit velocity is also higher.
-By using a conventional body that is strong in tight turns, it is possible to handle almost all types of circuits from low speed to high speed.
- In addition, improvements have been made to improve road-following performance, such as extending the suspension stroke and changing the oil dampers and springs.
- In addition, the EP model is equipped with new parts that can neatly organize the wiring, which can be a source of trouble, and prevent unexpected troubles such as contact of wires with the drive part.
- With increased performance and increased reliability, the Inferno MP10e TKI2 has everything you need to win races.
-Evolution of high-performance racing buggy with each part optimized for EP while based on high-performance GP model
- Enjoy driving in a wide range of driving fields, electric version with low running cost
- Uses a shaft-type 4WD system that is attractive for driving stability and high reliability
- The main chassis is made of duralumin, which has both moderate flexibility and high rigidity. Resin side guards are also installed.
- Equipped with a highly rated receiver box even in conventional models, protecting the receiver from dust and sand
- Equipped with an ESC dedicated mount that is easy to maintain because it can be attached and detached with screws.
- Diaphragm-type oil damper, which has a reputation for high damping capacity and stable operation, is adopted.
- Enlarged suspension stroke greatly improves driving stability and gap running performance
- It is possible to change settings and improve performance by using optional parts for the existing Inferno MP10 series.
[Technical data]
- Total length 490mm
- Width 307mm
- Overall height 180mm
- Wheelbase 325mm (changeable with rear hub color)
- Tread (F/R) 254mm
- Tires (F/R) sold separately
- Gear ratio 10.14:1
- Gross weight about 3,650g
[Kit contents]
- Complete assembly kit
- clear body
- window mask sheet
- pinion gear
- decals
- Hex L-shaped wrench (1.5/2.0/2.5/3.0mm)
- cross wrench
- Ring gear grease
[What you need before running]
- Each company's 2-3ch transmitter/receiver
- Servo Recommended: Torque of 15kgf cm or more from each company
- ESC Recommended: 1/8 brushless ESC from each company
- Motor Recommended: 1/8 brushless KV1900~23000
- Tire and tire inner for 1/8 buggy
*We recommend that you check the set that matches your driving location in advance.
- wheels
Recommended: Hard dish wheel (4 pieces/white) [IFH006W-H]
- Silicone oil for differential
Basic setting: Front #4000 [SIL4000B] Center #6000 [SIL6000B] Rear #3000 [SIL3000B]
- Silicone oil for dampers
Basic setting: Front #550 [SIL0550-8] Rear #450 [SIL0450-8]
- body paint recommended: spray for polycarbonate
- Battery for running (2 x 2-cell Lipox) *4-cell pack battery not possible
・Recommended: Gens ace LiPo HV 6000 (100C/7.6V/LCG)[GAB1202PB]
- Charger Charger for each company's lipo battery
・Recommended for charging: Gens ace LiPo Battery Porotector (2-6 cells/for charging) [GAC0100B]
・Recommended when charging: Gens ace LiPo battery safe back (BOX type) [GAC0101]
- Various tools Recommended:
・KANAI TOOL Hex Wrench Driver (1.5mm) [YKW015B]
・KANAI TOOL Hex Wrench Driver (2.0mm/Titanium Coated) [YKW020TC]
・KANAI TOOL Hex Wrench Driver (2.5mm) [YKW025B]
・KANAI TOOL Hex Wrench Driver (3.0mm) [YKW030B]
・KANAI TOOL slotted screwdriver (3mm/long) [YKW005B]
・Spanner set (5.5-7.0/6.5-8.0) [YKW102]
・SP knife edge reamer [36219]
・KRF Stainless Polycarbonate Body Cutter Straight [36261B]
・KRF Stainless Polycarbonate Body Cutter Curve [36262B]
・Needle nose pliers
·cutter knife
・Nippers
( This is a machine translation. Please allow for possible misinterpretations in the text. )