Product Description

--The product is an unpainted kit that requires adhesive assembly and painting.
--The scale is 1/700, and it is an offshore model that does not include the bottom of the ship.

[Products can be selected from multiple annual states]
――The last appearance of a sortie to Okinawa with Yamato by Operation Ten-Go in April 1945, equipped with 28 25mm single machine guns.
--After the Battle of the Philippine Sea from the end of June 1945, 18 25mm single machine guns were installed, before the shape of the aviation work deck was changed.
--At the time of the Battle of the Philippine Sea in June 1945, it is said that the single machine gun had not been strengthened.

[Preparing and enclosing parts that correspond to the annual changes of Yahagi]
--The support tube of the high-angle rangefinder is made into a separate part in response to the change in shape between 1945 and 1945.
――The aviation work deck is a special part that corresponds to the shape of the opening and corresponds to two types of yearly differences.
-The deck near the stern is two types of special parts to reproduce the appearance that the equipment is different depending on the year.
--There are two types of dabits on both sides of the front of the bridge, one for deployment and one for storage. The former is for 1945 and is used when the ship-mounted boat is not unloaded.

[Reproduce the characteristics of the third ship Yahagi, which is different from the sister ship]
――The bridge is made exclusively for Yahagi so that the shape difference can be clearly reproduced.
-Unlike the smell of sake, the main gun canopy has a special part with a small aiming hand window on the front left of the canopy.

[Reproduce the modern Agano-type shape that is different from the flow of Japanese light cruisers until then]
-The hull is a left-right bonding type, and the portholes are closed and the number is reduced compared to when it was completed.
――The port side electric circuit that runs all around the side is a delicate sculpture that even expresses the fastener part.
-On the deck and each layer of the bridge, the holding metal fittings that express the linoleum floor and the anti-slip / strip pattern of the iron deck are expressed with sharp sculptures.
-The shelter part in front of the bridge is integrated into parts using a slide mold.
-For precise engraving and modeling on the side wall.
-The main turret is a slide mold that reproduces windows and rattal / steel plate seams on the sides and top.
――The grid at the top of the chimney is removed for realistic modeling, and the internal rectifying plate is also three-dimensionalized as a separate part.
-The chimney is a left and right sticking type, and the monkey rattal is also engraved. Each steam pipe is an independent part and expresses the difference from the sister ship.
--The triangular pyramid truss at the bottom of the mast is pulled out using a slide mold.
--The small cranes on both sides of the rear end of the aviation work deck are three-dimensionally and accurately reproduced with separate parts.
--The 4.5-meter high-angle rangefinder accurately shapes the columnar arm shape or is enclosed as a special part.
――No. 22 electric probe, ramp (storage), directional detection antenna, auxiliary wing storage, etc. are all made into separate parts.
--The long 8 cm twin high angle gun is recorded as a new specially designed product with the shield and barrel as separate parts.
――The water reconnaissance crane reproduces even the light holes on the side to improve the sense of precision.
--The on-board seaplane includes two zero-type (three-seater) seaplanes. The molding color is gray.

[Two types of attached decals]
-There are two types of attached decals, including the warship flag, the sun flag, and the markings of the carrier-based aircraft.
--Three sizes of warship flags are available.
--Recorded with 1/700 scale of the actual 10 width, 6 width, and 3 width.
--The Hinomaru of the carrier-based aircraft, the identification band (yellow belt), etc. are recorded, and the Hinomaru includes those without a white border in the latter half of the war.
-A decal that includes the draft notation, the chrysanthemum flower emblem on the bow, and the ship name notation on the stern (two types, gold and warship color painting).
-Type 96 25mm machine gun (triple / single) can be selected from 2 types of quality parts.
-Precise shape with separate parts for the barrel and pedestal, a structure that makes it easy to paint separately.
――A design that fits in the adhesive position by combining the gantry and the barrel runner, and cuts the gate after using the pouring adhesive.
――The molding color is gray for the gantry and gun metallic for the barrel, so you can express it in different colors without painting.
――The bulletproof plate of the triple cannon is also a separate part, so it can be made more precise.
――The other type contains a conventional integrally molded type.
――The molded parts are composed of three colors: gray, transparent, and gun metallic, which imitate the color of Kure Naval Arsenal.
--208 assembled parts (in the case of 1945)

[Attachment]
--Runner x29
--Assembly manual x1
--Decal x2


Item Size/Weight : 40.7 x 14.6 x 6.1 cm / 316g

Product Specifications

Country

Japan

Item code

433240

JAN code

4968728433240

Purchase Information